Pypes-performance-exhaust SFM68 Bedienungsanleitung PDF herunterladen

SFM62V/ SFM65/ SFM68

Stainless Steel header/cross-member back exhaust system for

2005-10 Ford Mustangs

SFM62V: 05-10 GT 409 Stainless Cat-back w/ Violator Axle-back.

SFM65: 05-10 V6 409 Stainless cat-back when using GT take-off’s

SFM68: 05-10 V6 409 Stainless complete cat-back dual exhaust

Thanks again for purchasing your new stainless steel Pypes Performance

Exhaust 05-10 Ford Mustang GT or V6. Please be sure to conrm all the

components in the kit were received in your shipment before beginning

installation. If you nd any components missing, please contact our ofce

at 800-421-3890 for replacement. Installation of these kits will require a few

simple tools: jack stands, 13mm & 15mm wrenches, cutting device and pen-

etrating oil. For a quicker and tighter installation, air tools are recommended.

Technical assistance is available both online at www.pypesexhaust.com or

800-421-3890.

Pypes Performance Exhaust

2880 Bergey Road Unit O Hateld, PA 19440

800-421-3890 (voice) 215-712-9968 (fax)

www.pypesexhaust.com

(A) After-Cat X-pipe

(SFM68 only)

(B) Mid-pipes

(A)

(B)

(C)

1. Begin by placing the vehicle on a lift or four jack stands at maximum height. This

will aid in an easier installation.

2. Before unbolting any part of your existing system, match up the two hangers

on your new x-pipe to the existing H or Y pipe mounts on the car. You will need to mark

where the cuts are to be made on your factory H or Y pipe. This line should be 8-9 inches

from the factory cats. Once you have checked the measurements, make the cuts through

both driver and passenger pipes.

3. You can now remove you factory Y or H pipe section. V6 owners can also

remove the single mid pipe and single axle back. V8 owners will need to remove both mid

pipes and the axle-back mufers.

4. It’s time to install your new Cat-back system. Begin by installing the two band

clamps on to the after-cat x-pipe. Place the x-pipe hangers in the factory mounts near the

transmission. Snug the clamps but do not tighten yet. Next install the two mid-pipes and

the band clamps connecting the mid-pipes to the new x-pipe. Snug also but do not tighten.

5. Next install the new axle-back system. Begin by installing the two band clamps on

to the mufer necks. Place the factory hangers in the right conguration on to the welded

wire forms on the axle-backs. Slide the mufer necks on to the mid-pipes, and then bolt

the hangers on to the frame rails. Once all the hanger bolts are tight, make sure the tip

is adjusted properly in the bumper cut-out (see below for V6 owners) and now tighten the

band clamps on you x-pipe mid-pipes and axle-back...

6. For V6 owners: Use the passenger side as a reference for your new GT hanger

placement. Your car has all the threaded nuts welded into the frame rails. Proper place-

ment is necessary. Also if you are still utilizing your factory V6 rear bumper cover, use the

template provided to trim out the opening on the drivers side.

7. Check all the connection points periodically, as they may come loose.

Note: If you nd the new tips are not aligned properly in the bumper cutouts, you may

need to adjust your mid-pipes by loosening the two band clamps located where your fac-

tory h-pipe meets the mid-pipes. A slight rotation of the mid pipes will allow for the best t.

Now it’s time to re up that muscle car and enjoy your

new Pypes Performance Exhaust.

(C)

SFM25 does not

include this Axle-

back System

Inhaltsverzeichnis

Seite 1

SFM62V/ SFM65/ SFM68Stainless Steel header/cross-member back exhaust system for 2005-10 Ford Mustangs SFM62V: 05-10 GT 409 Stainless Cat-back w/ Vi

Verwandte Modelle: SFM65 | SFM62V |

Kommentare zu diesen Handbüchern

Keine Kommentare

Pypes-performance-exhaust SFM68 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Pypes-performance-exhaust SFM68 herunter. Pypes Performance Exhaust SFM68 User Manual Benutzerhandbuch

Inhaltsverzeichnis

Verwandte Modelle: SFM65 | SFM62V |

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Pypes-performance-exhaust SFM68