Pypes-performance-exhaust SFM69 Bedienungsanleitung PDF herunterladen

SFM66 / SFM66M / SFM69

409 Stainless Steel Mid-mufer Cat-back exhaust system for

2005-10 Ford Mustangs

SFM66: 05-10 GT Mid-Mufer Cat-back System

SFM66M: 05-10 GT Mid-Mufer Cat-back w/ “PypeBomb” axle back

SFM69: 05-10 V6 After-Cat Mid-Mufer System

Thanks again for purchasing your new stainless steel Pypes Performance

Exhaust 05-10 Ford Mustang GT or V6. Please be sure to conrm all the

components in the kit were received in your shipment before beginning

installation. If you nd any components missing, please contact our ofce

at 800-421-3890 for replacement. Installation of these kits will require a few

simple tools: jack stands, 13mm & 15mm wrenches, cutting device and

penetrating oil. For a quicker and tighter installation, air tools and welding

are recommended. Technical assistance is available both online at

www.pypesexhaust.com or 800-421-3890.

Pypes Performance Exhaust

2705 Clemens Road Bldg 105A Hateld, PA 19440

800-421-3890 (voice) 215-712-9968 (fax)

www.pypesexhaust.com

(A) After-Cat X-pipe

(SFM69 only)

(B) 16” Mid-pipes

(C) M-80Mufers

(D) Over-axle

Mid-pipes

(E) Mufer-delete

Tailpipes

(F) 4” Round Tips

(A)

(B)

(D)

1. Begin by placing the vehicle on a lift or four jack stands at maximum

height. This will aid in an easier installation.

2. Unbolt the existing system from just behind the factory h-pipe using a

15mm wrench on the band clamps. Loosen the clamps at the factory axle-

backs with a 15mm wrench. Now remove the factory mid-pipes. Last, unbolt

the factory mufer hangers using a 13 mm wrench and drop the axle-backs

from the vehicle.

3. You can now re-install the four axle back hangers on to the frame

rails. Leave the bolts loose until the entire system is installed.

4. It’s time to install your new Cat-back system. Begin by installing the

two 16” slight bent pipes to the factory h-pipe (straight end towards the h-pipe

and slight bend towards the mufers) using the factory band clamps. Snug the

bolts with a 15 mm wrench.

5. Next install the new M-80 cylindrical mufers onto the short pipe

(slight bend towards the mufers and the straight portion into the clamps at

the h-pipe). The HVC21 band clamps will be used at both the inlet and outlet.

These will appear to be very close o the drive shaft.

6. Next, install the over the axle portion on the mid-pipes, and slide the

axle-back mufer delete tailpipe wire forms into the factory mufer hangers.

SFM66M uses the “PypeBomb” axleback to nish the system. Use an HVC21

band clamp at the connection between the mid-pipes and the tailpipes.

7. Finally, slide the EVT 52 tips on to the tailpipes, SFM66/69 only.

Clamp the tip on using a HVC21 band clamp.

8. Finish the system by making all your nal adjustments to position

the mid pipes, mufers and tailpipes. Now tighten all the band clamps or for

the best t weld all the slip joints. The 409 stainless can be welded with your

standard Mig welder, and is highly recommended when possible.

9. Check all clamped joints periodically as they may come loose.

Note For V6 owners: Please refer to the installation instructions

for XFM44 After-cat x-pipe. Use the passenger side as a reference for your

new GT hanger placement. Your car has all the threaded nuts welded into

the frame rails ( some 05-10 V6’s need the hole to be threaded with an M8

x 1.25mm tap). Proper placement is necessary. Also if you are still utilizing

your factory V6 rear bumper cover, you will need to trim out the opening on the

driver side, per the template provided.

Note: If you nd the new tips are not aligned properly in the bumper

cutouts, you may need to adjust your mid-pipes by loosening the two band

clamps located where your factory h-pipe meets the mid-pipes. A slight rota-

tion of the mid pipes will allow for the best t.

Nowit’stimetoreupthatmusclecarandenjoyyour

newPypesPerformanceExhaust.

(D)

(B)

(F)

(E) (E)

SFM66 / SFM66M / SFM69 1

Inhaltsverzeichnis

Seite 1 - SFM66 / SFM66M / SFM69

SFM66 / SFM66M / SFM69409 Stainless Steel Mid-mufer Cat-back exhaust system for 2005-10 Ford Mustangs SFM66: 05-10 GT Mid-Mufer Cat-back SystemSF

Verwandte Modelle: SFM66M | SFM66 |

Kommentare zu diesen Handbüchern

Keine Kommentare

Pypes-performance-exhaust SFM69 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Pypes-performance-exhaust SFM69 herunter. Pypes Performance Exhaust SFM69 User Manual Benutzerhandbuch

Inhaltsverzeichnis

Verwandte Modelle: SFM66M | SFM66 |

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Pypes-performance-exhaust SFM69