Pypes-performance-exhaust HFM26 Bedienungsanleitung PDF herunterladen

HFM23

1. Begin by disconnecting your negative cable from your battery, as you will need

to unplug and remove your O2 sensor harnesses. Place the vehicle on a lift or four jack

stands at maximum height. This will aid in an easier installation. Note: Make sure to

support your mid-pipes just past the connection point between the factory h-pipe.

2. Unbolt the factory band clamps connecting your h-pipe to your mid-pipes.

Soaking your factory mounting points with penetrating oil will allow for easier removal.

Next, disconnect your three 02 sensors from the factory wiring harness and remove

them from the h-pipe using a 22mm wrench. Last, remove the four bolts at the manifold/

header end. Slide the h-pipe out of the factory hangers and remove.

3. Now it’s time to install your new h-pipe. Begin by installing the driver and pas

senger legs of the h-pipe rst. The leg with the two O2 sensor holes is the passenger

side. Now install the rear h-pipe into the factory hangers. Don’t forget to slide the 1”

wide band clamps onto the expanded portion of the h-pipe. The welded area of the wire

forms should face the ground or be on the bottom. The 2-1/4 “ u-clamp is used to clamp

the center portion of the “h” together. Welding of this pipe is highly recommended.

4. Complete the install: Snug the two clamps at the slip joints between the down-

pipes and the h-pipe. Make all nal adjustments to the h-pipe and tighten all the clamps.

Don’t forget to reinstall the factory band clamps at the rear connection between the

h-pipe and the mid-pipes.

5. Last install your three 02 sensors and reconnect them to the factory harness.

After all the connections are tight, start the engine. Check and listen for any leaks.

Make sure to check your connections periodically as they may come loose.

Note: On some years, the manifold connection will not seal even with the sleeves inserted into the downpipe legs. If this

problem occurs, you must back out the factory studs and install (2) HELP/Motormite stud kit # 03102.

HFM23 / HFM26

409 Stainless Steel 05-10 Ford Mustang GT H-pipes

HFM23: 2005-10 GT Modular Off-Road H-pipe

HFM26: 2005-10 GT Modular Street-Legal H-pipe

Thanks again for purchasing your new 409 stainless steel Pypes Perfor-

mance Exhaust 05-10 Ford Mustang GT H-pipe. Please be sure to conrm

all the components in the kit were received in your shipment before begin-

ning installation. These kits will include your new h-pipe with 02 bungs and

installation hardware. If you nd any component missing, please contact our

ofce at 800-421-3890 for replacement. Installation of this kit will require

a few simple hand tools, a cutting device and penetrating oil. For a quicker

and tighter installation, air tools are recommended. Technical assistance is

available both online at www.pypesexhaust.com or 800-421-3890.

Pypes Performance Exhaust

2705 Clemens Road Bldg 105A Hateld, PA 19440

800-421-3890 (voice) 267-638-3507 (fax)

www.pypesexhaust.com

(A) Front Legs

(B) H-pipe Assembly

(A)(A)

HFM26: (HFM23 & CVM10K)

1. Begin by disconnecting your negative cable from your battery, as you will need to unplug and remove your O2 sensor

harnesses. Place the vehicle on a lift or four jack stands at maximum height. This will aid in an easier installation. Note: Make

sure to support your mid-pipes just past the connection point between the factory h-pipe.

2. Unbolt the factory band clamps connecting your h-pipe to your mid-pipes. Soaking your factory mounting points

with penetrating oil will allow for easier removal. Next, disconnect your three 02 sensors from the factory wiring harness and

remove them from the h-pipe using a 22mm wrench. Last, remove the four bolts at the manifold/header end. Slide the h-pipe

out of the factory hangers and remove.

3. Since you are using this as a street legal h-pipe, you will need to cut 9-1/2 inches off the rear sections of the down-

pipes to install the cats. Also make sure the O2 bung on the drivers leg and the rear bung on the passenger leg are plugged

and tight as the new cats will accept the O2 sensors.

4. Now it’s time to install your new h-pipe. Begin by installing the driver and passenger front legs of the h-pipe rst. The

leg with the two O2 sensor holes is the passenger side. Slide the 1” wide band clamps on the slotted portion of the catalytic

converters. Slide converters over the down-pipes. Next slide the last two 1” wide band clamps on to the expanded front por

tion of the h-pipe. Now install the rear h-pipe into the factory hangers. The welded area of the wire forms should face the

ground or be on the bottom.

5. Complete the install: Make all nal adjustments to the h-pipe and tighten all the clamps. Don’t forget to reinstall the

factory band clamps at the rear connection between the h-pipe and the midpipes.

6. Last install your three 02 sensors and reconnect them to the factory harness. You rear tow O2 sensors will thread

directly into the bungs in the rear of the catalytic converters. After all the connections are tight, start the engine. Check and

listen for any leaks. Make sure to check your connections periodically as they may come loose. Available is an optional cat

delete kit for, $20.00 shipped to an address in the continental 48 states, if you wish to convert back to an off-road h-pipe in

the future.

Now it’s time to re up that muscle car and enjoy your new Pypes Performance Exhaust.

(B)

Inhaltsverzeichnis

Seite 1 - HFM26: (HFM23 & CVM10K)

HFM231. Begin by disconnecting your negative cable from your battery, as you will need to unplug and remove your O2 sensor harnesses. Place the vehic

Verwandte Modelle: HFM23

Kommentare zu diesen Handbüchern

Keine Kommentare

Pypes-performance-exhaust HFM26 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Pypes-performance-exhaust HFM26 herunter. Pypes Performance Exhaust HFM26 User Manual Benutzerhandbuch

Inhaltsverzeichnis

Verwandte Modelle: HFM23

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Pypes-performance-exhaust HFM26